Manufacturers

My Profile

How to Get a Shipping Quote

1. Add an item to your cart
2. Either Go to the My Cart Box & Click "Get Shipping Quote" or Click Yellow Bar "Shipping:Click to Estimate"
3. Put in your State and Zip Code
That's all there is to it-no need to put your information in until you are ready to place your order!

My Cart

Your Shopping Cart is Empty

Blowout Specials

FREE Shipping

Free Ground Shipping* on any order $250 or more!
Click on Shipping to review our shipping policy

Home > Air Conditioning > A/C Leak Detection > Leak Stop Products

FJC 9165-6: Kwik Seal Stop Leak Aerosol Can w/Charging Hose- Case/6

Hover over image to zoom

More images

Click to enlarge

Price: $123.65

Product ID : 9165-6

Manufacturer: FJC

0 review(s)

E-mail to a friend

Please complete this form.
All fields are required.

Your name

Your email address

Your friend's name

Your friend's email

Purchase

The selected item is out of stock, please select a different item or combination

Description

**NO SHIPPING TO CALIFORNIA, WISCONSIN, PUERTO RICO OR HAWAII DUE TO STATE LAWS** PRODUCT CAN ONLY SHIP GROUND

As seen on "Two Guys Garage" Show on the Speed Channel!

"autoplay":"true","scale":"tofit","src":"http://www.wholesalepartsandtools.com/images/FJC9165-Two-Guys-Garage-Commercial-2009.mp4"

**Product cannot ship with Expedited Shipping-must ship Ground.It cannot ship to California, Wisconsin, Hawaii or Puerto Rico**
Kwik Seal Stop Leak 9165 in an Aerosol Can with a Charging Hose- Case of 6
- Advanced formula STOPS LEAKS where others fail!! Stops leaks in Condensers, Evaporators, Hose Connections, Gaskets and O'Rings
- Perfect for the Do-It-Yourself mechanic
- If your refrigerant leaks down in about 4-5 days then this product will work for you!
- Seals most leaks in all metal and rubber components
- No Stop Leak product will seal a compressor shaft seal leak
- Kwik Seal Stop Leak creates a permanent seal
- For use in R134a systems only
- Kwik Seal Stop Leak will not damage A/C Recovery/Recycle Equipment
- Add Kwik Seal Stop Leak to any R134a automotive system to prevent leaks
**Includes an easy-to-use hose with R134a quick coupler- No other tools are needed**

Easy to Install Kwik Seal Stop Leak
- Step 1: System must be fully charged with refrigerant prior to using this product. Locate A/C low side R134a service port, remove cap and push yellow hose connector on to the fitting
- Step 2: PushLok™ fitting locks on to service port allowing easy, hands free installation of Kwik Seal Stop Leak
- Step 3: Start vehicle engine and set A/C controls to MAX COOL
- Step 4: Depress the push button on the can to allow entire contents to enter the A/C system. Remove Kwik Seal Stop Leak connector and replace the service port cap. Allow vehicle to run for a minimum of 15 minutes with the A/C on.

For a single can see FJC 9165
Need a Stop Leak for an R12 system? See FJC 9160
Testimonials
2/17/09:

During a recent hot spell I discovered my 1999 Chevy Malibu was blowing warm air. I tried to recharge the A/C system but the high pressure side would not go above 70 PSI indicating there was probably a leak somewhere. Kwik Seal is a trusted name in stop leak products so I purchased a can of FJC 9165 Kwik Seal Stop Leak and installed it in the A/C system following the instructions on the can. I was then able to recharge the system with R134a until the high pressure side read 150 PSI. The A/C in my car now blows cold air just like it's supposed to.

I purchased the FJC 9165 Kwik Seal Stop Leak primarily because it stated it was safe for A/C recovery and recycle equipment. This product was very easy to use since it came with a charging tube, it performed as advertised, and probably saved me over $1,500! This is a great product and I would definitely recommend it to my friends. R.S